=========kosong=

Canon S Series Reset Procedures



Waste Ink Counter Reset.

1.Turn off the printer.
2.Press and hold the RESUME button, then press and hold the POWER button.
3.Release the RESUME button, Next press and release the RESUME button two(2) more times in succession.


Note: you are still holding the POWER button). The printer’s carriage will “reset” or move momentarily. If the above was properly performed the printer will enter the “Service Mode”.

4.Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.

-Service/Factory test printout, including ink sensor check.
-EEPROM - Info printout.
-EEPROM - Initialization.
-Reset the Waste ink counter.
-Printer model setting. (More selections beyond this point "However it is best leave them unaltered" You have been warned!)

After selecting the desired mode (eg 4), press the POWER button to “set” the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Continue reading..
Label:

Canon i320 i255 Waste Ink Counter Reset




Manual for Service Mode Canon i320 i255 Waste Ink Counter Reset
METODE 1 :
  • Unplug power and USB.
  • Open door and hold power button.
  • Connect power.
  • Close door, then release power button.
METODE 2
  • Turn off the printer. And disconnect the printer cable.
  • Press and hold the POWER button, turn on the printer.
  • The indicator (L.E.D.) should be green.
  • Press and release the RESUME button , the indicator (L.E.D.) should be orange.
  • Press and release the RESUME button again, the indicator (L.E.D.) should be green.
  • Release both buttons.
Continue reading..
Label:

Canon BJC-2100SP Waste Error Reset

Canon BJC-2100SP Waste Error Reset
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Open Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Continue reading..
Label:

Canon BJC-5000 Waste Ink Counter Reset


  • Power off printer
  • Press and hold RESUME then press POWER, The indicator will start blinking.
  • While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
  • When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
  • Press Power to set data
  • FINISH
Continue reading..
Label:

Refill Ink Instructions

Cartridge Canon BCI-60, BCI-61, BCI-62 Refill Ink Instructions :

1. The filling holes are located under the label as shown. Just peel back the label leaving it still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to widen the filling hole(s) in the top of the cartridge(s).
3. Connect the needle to the syringe and fill with ink.
4. Insert the needle into the widen filling hole. Note: This cartridge has a sponge so you may feel a slight pressure. Inject about 10 ml. of ink, per color until the ink bubbles up.
5. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per printer instructions
Continue reading..
Label:
Subscribe to: Posts (Atom)