Canon Resetters Blogs

Here is the way to Reset Canon PIXMA MP2371

-Download Resetter Canon MP237 on the link I have included at the end of this article
-Extract and run reseter MP237 by clicking 2 times File Service tool v3400.exe
-Start doing govern software reseter MP237
         Sub Tab Clear Ink Counter to Play
         Sub-Tab Ink Absorber Counter to Play
-Click EEPROM then the printer prints a sheet of paper
-Turn the printer off and on again, then you can use the printer again

Download the tools Reset Printer Canon MP 237 here

When you got error on your Canon MP287 it will make you confusion and you see error code is E08 and E13 , When the printer is turned on , the printer looks normal. But after ordered to print, it will display an error E08 i'm sure you already know if you come to this page. don't worry i know the solution. the printer need to be rese.

This is the way to reset Canon MP287 bicause of error E08


- Turn off the Canon MP287 error E08 by pressing power. Do not unplug the power cord .
- Press and Hold the STOP / RESET followed by pressing the POWER button . So both buttons depressed position .
- Remove the STOP / RESET but do not release the POWER button .
- In circumstances POWER button still depressed , press the STOP / RESET 6 times.
-Then release both buttons simultaneously .
- Printer will initialize error moments like when the printer is first tested at the time of purchase.
Wait until the LCD panel on the printer error was showing Black ( blank ).
-MP258 printer will be detected as a new device on your computer, although it was already installed the printer driver. -Conditions of blank printer on the LCD indicates that the printer is in Service Mode state and is ready to be reset using software .
- If the power cord is unplugged , then the steps above must be repeated again.

Now you can reset the Canon MP287 with this tools

get from this source hope this step will help you and make your printer can work again.

MP150/MP160 ERROR CODE
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full

E28 Ink cartridge temperature rise error -
E29 EEPRsaya error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

This mortal direct manual is practical for Canon i950 Apologise Strategy Jet Machine. Look you module perceive absolute statement of Ravine Machine i950 features and how to use them. Communication of the intruction: Basal Printing (Turning on the Machine, Weight Production, Using Primary Media, Writing with Windows, Printing with Fabric); Innovative Printing (Applications Included in the CD-ROM Assemblage,

Writing Borderless Photographs with Windows, Writing Borderless Photographs with Mack, Accessing Printer Utility, Adjusting Exposure Degree for Photographs, Using Machine Utility Options); Publication Upkeep (Exchange an Ink Vessel, When Publication Becomes Syncope or Colors are Erroneous, Writing the Nose Curb Nous Cleansing, Indication Knowledge Wakeless Cleaning, Aligning the Pic Progression); Troubleshooting (Cannot Set the Machine Wood, Pic Quality is Impecunious or Contains Errors, Troubleshooting Machine Constituent, Medium Does Not Provender Right, Touching Mistake Messages, An Happening Content Appears on the Display). Avaliable the Canon i950 Alter Belch Jet Printer User Draw Intruction

The Canon PC-170 was the first "personal copier" I ever bought. I needed something to duplicate invoices and receipts but didnt need the large scale copiers that seem to dominate the market.

The PC-170 seemed ideal. Its small and reasonably light at something like 19 pounds. It folds up to resemble a briefcase so it can be portable if you dont mind the weight. It means though I can store it away in my office at home and just get it out a couple of times a month when I do my accounting. Space is an issue for me so its nice to have something small that I can put away when I dont need it.

I have a Canon printer too, which is why I went for another Canon product. They are completely reliable, easy to maintain and cheap to run. The Canon instant on function is a joy to work with. Even though 10 seconds isnt a long time, over a couple of years it can be, so saving at least that much time in a day means a lot.

Once its working the PC-170 is very easy to use. To get it up and running you just need to unpack it and connect it up. Once plugged in, there is no warm up time, so its ready a second or two later. Canon has a clever kind of ink that doesnt need to be heated up like others, which is why its always ready.

The ink cartridges themselves are an all in one. That means I only have to change a single item to keep the copier going forever. The drum and fuser are in with the toner, which makes it very easy to maintain. At $40 each for 4000 pages, that lasts me a good few months.

You cant write about a copier without mentioning whether its any good or not. The PC-170 is good. I only mainly copy receipts and invoices but occasionally Ill copy something useful in a newspaper or magazine, like a recipe or a how-to guide. The copier handles them well, even the photographs. Even though the copier is black and white, the photos still come out well. They are nicely detailed and dont really look like old fashioned black and white, they are more crisp and exact.

The PC-170 is a great little copier. Small enough to be convenient in confined spaces, but good enough to be able to produce what you need.

The Canon Copier ImageClass D320 is a desktop laser printer copier aimed at the home market. Small businesses may also benefit from it as long as their duty cycle wasn’t too demanding.

Setup of the D320 is about as quick and easy as it gets. Simply unpack it, insert the toner, connect it and off you go. It has USB2 so attaching it to a computer is just a matter of plugging it in and loading the drivers. The chassis itself is a compact one. It leans to the right as the platen and paper tray both extend past the body to cope with legal sized media.

Copy and print quality is good enough for business use. The 1200 x 600 dpi resolution produces text that is clean, crisp and precise. Images and photographs are also well presented, with sharp edges, fine detail and even coverage. Text is well printed, finely edged and evenly toned. At 15 pages per minute there isn’t much waiting around for your copies either.

The paper tray can cope with 250 sheets of paper and the output tray around 15. The paper has a tendency to curl if left too long on the output so it’s best to remove it at it comes out. Especially if you’re planning on printing or copying double sided.

Replacement toner will set you back around $33 and will print around 3500 pages. It is a single cartridge system which needs no drum or developer unit for it to work. So not only is it good value for money, it’s easy to manage too. This setup is typical of Canon printers and copiers right now. It reduces running costs, manufacturing costs and waste. The added bonus is that you only need to change one consumable.

The D320 is a decent printer and copier that will serve you well if you’re a light user. It’s efficient, easy to set up, and use. The print quality is good, as is copy quality. Both functions are well featured and produce results that are more than fit for purpose.

• Unplug power and USB.
• Unplug power and USB.
• Open door and hold power button.
• Connect power.
• Close door, then release power button

Refill intructions for Canon Inkjet Cartirdge PG-30, PG-40, PG-50, CL-31, CL-41, CL-51 and CL-52.

1. Remove the label from the top of cartridge
2. Using the drill tool, widen the refill holes for each color.
3. Prepare an area for refilling.
   
4. Attach the needle to syringe and load syringe with 6ml of ink (For color cartridges) position for the 41, 51, 52 cartridges or 20ml for the black 40 and 50 cartridges.
5. Insert needle into correct color ink hole (that you created in the vent). Penetrate the sponge inside and be sure the needle does not reach the bottom of cartridge. If the needle penetrates to the bottom of the cartridge, the cartridge will leak and is not salvageable.
6. SLOWLY inject the ink into the cartridge. Stop if the ink begins to well up from the fill hole. Reverse the process and pull about 1ml of ink if it has spilled out the top of the cartridge.
7. Clean off top of cartridge, un-tape the next fill hole and tape over the one just filled. This is so you don’t accidentally contamination other colors.
8. Repeat steps 5, 6, 7, 8 until all colors have been injected.
9. Clean off the top of the cartridge. Place tape over the top of the cartridge so it covers every hole.
10. Use a pin and put a small hole (vent hole) through the tape for each hole on the top of the cartridge. This is important, don’t skip this step. The cartridge must be vented to atmosphere or it will not work.
11. Reinstall the cartidge.

There are some ways to reset waste ink counter in the Canon Pixma iP 1880. Waste Ink counter have full at Canon Pixma iP 1880 marked with The POWER and ALARM lamps flash alternately. If waste Ink have full the printer cannot be used. So, the printer will be able to be used again after reset. You are can use software resetter like GeneralTool or iPTool to reset Canon Pixma iP 1880, you can also do reset manual. Following its way to reset Canon Pixma iP 1880 :

A. Reset Manual.

On reset manual, sometime printer return blinking after turn on again. For reset manual following its way :

• Turn the printer on
• Press and hold Resume button for 1-2 minutes
• Open the printer cover
• Release the catridge and then put catridge again
• Close The Cover
• Turn Off then Turn On again.

B. Using GeneralTool for canon pixma ip 1800 series

Before using GeneralTool for canon pixma ip 1800, printer driver should have been install correcly in the computer.

Using GeneralTool iP 1800...? why do not use GeneralTool iP 1880. Canon Pixma iP 1880 is canon iP 1800 series. Follow this intruction to reset the printer :

• Download software resetter for canon pixma iP1880 from Here
• Before connecting printer to the power suply, press and hold power button then connecting the printer to the power.
• While hold the power button press reject button for 2 times then release power button.
• Run general tool for canon iP 1880. After the printer know, Click lock release button. ( note : to view locK release menu, min resolution 1024 x 728).
• Then select Set Destination to iP1800 (my canon iP 1880 printer is iP1800ASA)
• Click MAIN and PLATEN button to reset waste ink counter to zero.
• Finally test print by click TEST PATTERN button.

C. Using iPTool software

This is software from Rusia for canon iP series. Using this software give separate experience. this software detect automatically attached printer in the computer. following way reset to use iPTool software :

• Download and ektrak iPtool software, you can download the software from this url : http://www.ipt.nm.ru/
• Turn on the printer
• Then run iptool software, the software will detect the printer automatically.
• To reset waste ink counter to zero click “Reset Main” and “Reset Platen” button.
• To view the result do test print.

well this really anoying when busy with the job, in the same time the print won't print the reaason is stuck haha this is some Solution to fix yhe problem

(1) Turn the printer off.
(2) On the right at the end of the printer path is a white, square piece of plastic with 2 small pieces of colorless plastic sticking upright (on the back side you should see a spring attached to the plastic piece). Gently place your finger on that plastic plate and try to slide it to the front of the printer until it dissapears from your sight (you should hear a click).

this is a few guide how to cleaning printer head on canon ip3000

STEP ONE: Lifted print head from printer. It pulls out easily because it is held in with the same swing down lever that holds the cartridges in place.
STEP TWO: put two layers of paper towel in bottom of dish to protect sensitive sprayer heads;
STEP THREE: put enough solvent in dish to just cover the screens on which the cartridges sit when in use;
STEP FOUR: took the two small screws out that hold the white ceramic piece;
STEP FIVE: gently pried ceramic piece back and away, to reveal underside (no need to pull away glued points on both sides);

this solution if you have problem with code Pixma MP600 Error Code 5010.
fisrt Please turn off the printer from the mains wall socket and unplug it from your computer. Take the paper out and put it back in, checking its all straight and no corners turned up etc. Then have a cup of tea (ie leave it for 5 minutes) Now plug it back in and switch on.
Allow it to warm up and try printing again.

There is an inner door (which is actually used for printing CD's) that you can pull down and gain more access to the carriage. Get a flashlight and a small mirror to inspect the contacts. Next thing to open the cover and when the head comes to the center, pull out the power cord. Then remove all of the ink cars and then the printhead and clean the contacts on the back of the head and those in the back of the carriage.

The only other thing to do is to take that ink cart back to Staples and see if they have a Canon printer demo there and test the ink cart, or get a new one.

Pixma MP970 that keeps showing Error 5100 have tried resetting with guide from a i550 and hjc4500 but I still have same problem I can only print half of a DVD but I can print all of any pages that I want to Any suggestion to this problem is greatly appreciate.

the 5100 is the carriage error and can be caused by 4 different sensors. First off the "Timing Strip" that passes through the back of the Carriage Assembly can be contaminated with ink spots and this needs to be cleaned. Open the cover and use your flashlight to examine the timing strip as much as you can see. You really don't have much access to this strip unless you remove the covers,..and doing that is considerable work. The other items that can cause this error are the sensor inside the carriage unit, the drive motor for the carriage asm, and of course the main logic card. However, 99.6% of the time it is the Timing strip which is easitly contaminated with splattered ink.

I have created Repair Manuals that can teach you how to disassemble and repair any Canon Printer but I can advertize or sell this product from this web site. If you want more information you will have to click on my USER ID and send me an email and I will provide more information. I don't have a Manual for the MP960 since I have not had one to repair, but I have all other cirtical information including the Canon Service Manual for the MP960.

The error code is standard for many of the late model MPxxx printers. The B200 error is "Printhead Temperature exceeded", What this means that while you were printing some document, either one or more of the printhead ink wells ran out of ink and the printing continued. Printhing without ink in the wells will OVERHEAT THE PRINTHEAD NOZZLES and can potentially burn the out. The printer has a built in temperature sensor to detect the ambient temperature and to monitor the temperature of the head. This data is always collected and monitored and saved in the EEprom data and the Service Test print data.

If the error will not go away once you have unplugged the priner for at least 5 minutes, then there is the possibility that you have already burnt out the head. Remove the printhead and use a 5x magnification glass to look VERY CLOSE at all of the nozzles to see if you can detect any possible burnt out nozzle. It many come down to need a new printhead.

Action
1. Contact
Is any of the contacts of the primary charging roller, developing assembly, or transfer charging roller soiled? Or, is there poor contact?
YES: Clean the contact, and set it once again.

2. Wiring
Is the wiring between the contacts for the following normal: DC controller PCB (J301), composite power supply PCB (J136), primary charging roller, developing assembly, transfer charging roller?
a. DC controller PCB (J301) <-> composite power supply PCB (J136)
b. composite power supply PCB (J130-7) <-> primary charging roller contact
c. composite power supply PCB (J130-1) <-> developing assembly contact
d. composite power supply PCB (FT133) <-> transfer roller contact
NO: Correct the connection.

3. Composite power supply PCB, DC controller PCB
Try replacing the composite power supply PCB. Is the problem corrected?
YES: Yes.
NO: Replace the DC controller PCB.