Canon Resetters Blogs

You can use SSC software or adjustment program to reset Epson R240, R245, R250. IF resetting using adjustment, no need date setting can be used in your computer.

Here how to Reset Epson R240, R245, R250 using adjustment program

1. Start with printer on.
2. Download and extract adjustment program for Epson R240, R245, R250.
3. run the adjustment program from extracted folder by clicking "adjprog.exe (or look for the application file or .exe file then run it).
4. click accept button
5. Set printer model and destination and then click ok
6. Select waste ink pad counter under maintenance option then click ok
7. Click read button to read the counter.
8. Click initialization to reset waste ink counter the Epson R240, R245, R250 and then finish
9. Restart your printer.

Reset Using SSCLG software (only for Epson R240)

* Download and install SSC serve software and then run it.
* Click configuration tab select epson stylus photo R240 in the printer model then close the configurations windows.
* Right click mouse on SSC icon in the systra then select "protection counter" and then select "reset protection counter"

Much people have problem for Epson CX5500 and Epson CX5505.This tutorial reset using adjustment program for Epson CX5500 and Epson CX5505.

here how:

• Execute the adjustment program (printer must be ON)
• Choose maintenance ink pad menu
• Click read
• Click initialize
• Read(again) after "0" press finish
• Choose set shipping data (bottom menu)
• Choose set
• Wait for a while (about 1 minute)
• If there is a reaction from the printer (it will load some paper or you hear "glodak" sound), the reset process will be done. turn off the printer and then turn on again. repeat read the EEPROM
• If there is no reaction from the printer, repeat step 1

have some information download link resetter epson T11 and resetter epson TX200, but I still have not tried this link is correct or not. I get this information from some forum.

Below for the download link for resetter epson T10 and TX200

Short Review of Epson Stylus TX300F

Canon BJC-5100-Self Test

* Switch Printer off
* Hold Power for 1 beep.

The Reset Procedure foe Canon BJC-5000 and BJC-5100

1. Switch off the printers
2. Press and hold RESUME button then press POWER button, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME button four (4) times. The indicator should be GREEN.
5. Press Power to set data

Service Test Print

1. Turn off the printer Canon BJC-5000 and BJC-5100
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME button two (2) times. The indicator should be GREEN.
5. Press the Power button to Print

Nozzle Print

1. Power off printers Canon BJC-5000 and BJC-5100
2. Press and POWER, until heard beeps sound from the printer and release.

Demonstration Print

1. While the printer in ON , Press and hold RESUME button until the printer plays a melody of beeps.

Canon MultiPass MP390 Multifunction Review

The Canon MP390 is a great multifunction printer for small homes. For most homes and small businesses, space is a consideration when buying office machines, which is exactly why multifunctions like the MultiPass MP390 from Canon are such a popular choice. By combining printing, copying, scanning, and fax functions into one convenient unit, you can save on valuable desktop space, while taking advantage of all the functionality normally provided by four separate peripherals. The MP390 can also print high-quality color photos directly from compatible cameras and memory cards.

Canon MultiPASS MP360

Canon MultiPASS MP360 is All-in-One (Printer - Copier - Scanner) multifunction Inkjet printer, designed for home and small office.

Manual Reset procedure Waste Ink Tank for Canon MP390 and Canon MP360 Just Follow this step to reset waste ink tank full:

1. Start with printer on, press aadditional functions, Scan, Copy, Scan. Now you should be in service mode.
2. Select Test mode which is like the last available selection
3. Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

* The menu will now say EEPROM Clear
* Select Ink count which is option (0) and press set
* Then press Stop/Reset Followed by the power button and then wait for it to restart.

Solution to reset the ink level for Canon MX300. The methode get from printer forum

1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The printes turns into a kind of factory mode...(wait for about 10 seconds, utils it says "Idle")
6. Press the ">" (next to the "OK" button) once."Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print..
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

Canon SmartBase MP730 All-In-One InkJet Printer short review

Canon SmartBase MP730 Photo offers you the best available quality in an easy-to-use All-in-One machine guaranteeing high speed and high productivity. The SmartBase MP730 Photo delivers top Canon photo print quality with 4800 x 1200 dpi and 2 picoliter consistent droplet size. The newly developed 'Micro-Nozzles' coupled with Advanced MicroFine Droplet Technology reduce graininess to ensure you of the clearest, crispest photo and text prints available. And, it prints and copies a phenomenal 22 pages per minute in monochrome and 14 pages per minute in color.

Manual Reset procedure for waste ink tank full error in Canon Smartbase MP730 printers:

• Hit the “menu”: Key
• Hit “Copy” Key
• Hit “#” Key
• Scroll thru the menu headings until you come to “Test Mode” - 12th heading
• Hit the “3″ button- this will bring up Eeprom Clear
• Hit “0″ button
• Hit the “Stop” button

CANON iP1200, iP1600, iP2200, iP4200, iP5200, MP150

Stage One (Hardware Reset)
1. Turn off the printer, and then unplug the power cord
2. Press and hold the POWER button printer using the index finger
3. Replace the power cord
4. Use your middle finger to press the Resume button 2 times
5. Remove your index finger from the POWER button
6. You have completed the first phase to reset Ink Tank Full Error
(blinking power light)

Second Phase (Software Reset) to Permanent
1. Download the application resetter (large file 9.7 MB)
2. Extract / Unrar in C: \ iP1200
3. Ensure that all file attributes from Read Only
4. Run GeneralTool.exe
5. In USB Port select your printer port
6. Select (check) EEPROM CLEAR
7. Provide blank paper to print, then click the Test Pattern 1
8. Finish, iP1200 and iP1600 printers you back to normal

Resetting canon pixma MP450, this methode reset to rese4t waste ink counter in the printer Canon Pixma MP450. Here how:

1. You must start with printer off and power cable connected to eectric source.
   
2. While press and hold Resume/Cancel button press POWER button- led indicator light in green color.
3. While hold Power button, release Resume/Cancel button.
4. press Resume/Cancel button for 2 times, while hold POWER button, after that, release all button.
5. When led indicator will be lit in GREEN - press Resume/Cancel for 4 times!
6. Turn off the canon pixma mp450 using POWER button.

Cartridge Canon BCI-60, BCI-61, BCI-62 Refill Ink Instructions :

1. The filling holes are located under the label as shown. Just peel back the label leaving it still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to widen the filling hole(s) in the top of the cartridge(s).
3. Connect the needle to the syringe and fill with ink.
4. Insert the needle into the widen filling hole. Note: This cartridge has a sponge so you may feel a slight pressure. Inject about 10 ml. of ink, per color until the ink bubbles up.
5. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per printer instructions