Canon Resetters Blogs

today not for canon, its for epson R230 that maybe reader need it.
Printer Epson R230 6 colors is very great for photo printing but sometimes blink alway make confused and annoying.This error cause you need to reset it. dont worry you can follow this guide to fix it

1. first Turn ON Epson R230
2. must download tools Epson R230 i will tell later
3. then when you have finish download extract open the sscserve.exe to install resetter
4. Result of install is "SSC Service Utility", and run this aplication
5. Ensure that the printer connection cable installed correctly
6. Choose 'Configuration' in SSC Service Utility V4.20
7. In 'Printer Model' option choose Epson Stylus Photo R220/R230
8. Look for printer image in right bottom toolbar on your computer monitor, and right click this printer image
9. Choose 'Protection counter' and left click 'Reset Protection Counter'
10. Turn OFF your Printer and Turn ON again, your printer should be normally

this tools is free for use you can get from here

• Unplug power and USB.
• Unplug power and USB.
• Open door and hold power button.
• Connect power.
• Close door, then release power button

Refill intructions for Canon Inkjet Cartirdge PG-30, PG-40, PG-50, CL-31, CL-41, CL-51 and CL-52.

1. Remove the label from the top of cartridge
2. Using the drill tool, widen the refill holes for each color.
3. Prepare an area for refilling.
   
4. Attach the needle to syringe and load syringe with 6ml of ink (For color cartridges) position for the 41, 51, 52 cartridges or 20ml for the black 40 and 50 cartridges.
5. Insert needle into correct color ink hole (that you created in the vent). Penetrate the sponge inside and be sure the needle does not reach the bottom of cartridge. If the needle penetrates to the bottom of the cartridge, the cartridge will leak and is not salvageable.
6. SLOWLY inject the ink into the cartridge. Stop if the ink begins to well up from the fill hole. Reverse the process and pull about 1ml of ink if it has spilled out the top of the cartridge.
7. Clean off top of cartridge, un-tape the next fill hole and tape over the one just filled. This is so you don’t accidentally contamination other colors.
8. Repeat steps 5, 6, 7, 8 until all colors have been injected.
9. Clean off the top of the cartridge. Place tape over the top of the cartridge so it covers every hole.
10. Use a pin and put a small hole (vent hole) through the tape for each hole on the top of the cartridge. This is important, don’t skip this step. The cartridge must be vented to atmosphere or it will not work.
11. Reinstall the cartidge.

There are some ways to reset waste ink counter in the Canon Pixma iP 1880. Waste Ink counter have full at Canon Pixma iP 1880 marked with The POWER and ALARM lamps flash alternately. If waste Ink have full the printer cannot be used. So, the printer will be able to be used again after reset. You are can use software resetter like GeneralTool or iPTool to reset Canon Pixma iP 1880, you can also do reset manual. Following its way to reset Canon Pixma iP 1880 :

A. Reset Manual.

On reset manual, sometime printer return blinking after turn on again. For reset manual following its way :

• Turn the printer on
• Press and hold Resume button for 1-2 minutes
• Open the printer cover
• Release the catridge and then put catridge again
• Close The Cover
• Turn Off then Turn On again.

B. Using GeneralTool for canon pixma ip 1800 series

Before using GeneralTool for canon pixma ip 1800, printer driver should have been install correcly in the computer.

Using GeneralTool iP 1800...? why do not use GeneralTool iP 1880. Canon Pixma iP 1880 is canon iP 1800 series. Follow this intruction to reset the printer :

• Download software resetter for canon pixma iP1880 from Here
• Before connecting printer to the power suply, press and hold power button then connecting the printer to the power.
• While hold the power button press reject button for 2 times then release power button.
• Run general tool for canon iP 1880. After the printer know, Click lock release button. ( note : to view locK release menu, min resolution 1024 x 728).
• Then select Set Destination to iP1800 (my canon iP 1880 printer is iP1800ASA)
• Click MAIN and PLATEN button to reset waste ink counter to zero.
• Finally test print by click TEST PATTERN button.

C. Using iPTool software

This is software from Rusia for canon iP series. Using this software give separate experience. this software detect automatically attached printer in the computer. following way reset to use iPTool software :

• Download and ektrak iPtool software, you can download the software from this url : http://www.ipt.nm.ru/
• Turn on the printer
• Then run iptool software, the software will detect the printer automatically.
• To reset waste ink counter to zero click “Reset Main” and “Reset Platen” button.
• To view the result do test print.

well this really anoying when busy with the job, in the same time the print won't print the reaason is stuck haha this is some Solution to fix yhe problem

(1) Turn the printer off.
(2) On the right at the end of the printer path is a white, square piece of plastic with 2 small pieces of colorless plastic sticking upright (on the back side you should see a spring attached to the plastic piece). Gently place your finger on that plastic plate and try to slide it to the front of the printer until it dissapears from your sight (you should hear a click).

this is a few guide how to cleaning printer head on canon ip3000

STEP ONE: Lifted print head from printer. It pulls out easily because it is held in with the same swing down lever that holds the cartridges in place.
STEP TWO: put two layers of paper towel in bottom of dish to protect sensitive sprayer heads;
STEP THREE: put enough solvent in dish to just cover the screens on which the cartridges sit when in use;
STEP FOUR: took the two small screws out that hold the white ceramic piece;
STEP FIVE: gently pried ceramic piece back and away, to reveal underside (no need to pull away glued points on both sides);