Canon Resetters Blogs

Before installing your catridges, is also highly recommended for you to check you registry status to make sure there is no conflict. You can scan your registry from this link click here

1. When you turn off the printer, then click STOP / RESET and the printer knopkuo POWER.
2. Without releasing the POWER LED lights up when the power button, press 2 times STOP / RESET
3. Release the power button, and then a second button - you hit your profile.
4. The indicator light green. Press STOP / RESET 4 times.
5. Turn off the printer.

1.Observe the indicator light on your printer to make sure it flashes eight times consecutively. This means you are experiencing error 1700, the Waste Ink Nearly Full Error.
2.Press the “Resume/Cancel” button on the printer to reset the error. You will also be able to finish the print job that you were performing when the error occurred.
3.Press the “Power” button on your printer if the error doesn’t automatically reset. Disconnect the data cable from the printer and unplug the printer’s power cord for 10 minutes.
4.Reconnect the data cable and power cord and turn the printer back on. The Waste Ink Error will be fully reset.
5.Find the closest Canon service store in your area (see Resources section) to fix the problem with the built-in waste ink absorber that is causing the error.

1. Press and hold both the "Stop/Reset" and the "Power" buttons on your printer.
2. Release the "Stop/Reset" button.
3. Push the "Stop/Reset" button two times, while continuing to press the "Power" button.
4. Release the "Power" button. Your printer is now in Service mode.
5. Insert paper into the paper tray.
6. Push the "Stop/Reset" button four times.
7. Press the "Power" button to turn off the printer. The printer will print counter information about the ink absorber before powering off. The printer will now work normally.

1. Place a document face-down on the platen glass.
   (Memo)
   Place a scanning side facing down on the platen glass.
   Align a document with the arrow (the alignment mark), which is at the bottom right corner of the platen glass.
   
2. Launch MP Navigator.
1. On the Windows desktop, double-click the 'MP Navigator 2.0' icon.
2. Alternatively, in the Windows taskbar, click 'Start', click '(All) Programs', 'Canon Utilities', 'MP Navigator 2.0' folder, then 'MP Navigator 2.0' icon.
   
3. Click 'Scan Photo/Document'.
   The Scan Photo/Document window will be displayed.

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter at the bottom of this post.

FIRST STEPS:   Entering Service Mode
You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.
2. Hold down STOP/RESET button and press Power button.
3. Keep holding down Power button and let STOP/RESET button go.
4. Then Press STOP/RESET button twice then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, extract it and double click "MP480.exe"
2. Click Reload Button and you will get a new USB port.
3. Load some papers in your printer and press the "Main" Button once, wait until the printing is done.
4. Then press "EEPROM Clear" button to clear EEPROM.
5. Then press EEPROM button and the printer will print some text.
5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

This error comes due to NV RAMof the printer. To diagnose this issue you'll need to reset the NV RAM of your printer, you can do that by entering the service mode. To do this turn on the machine. Press menu button the printer. Press scan button, then press copy and then scan button again to enter the service mode. Use > to go to NV RAM access. Set abs-m level to 0. Set abs-p level to 0. Press stop to exit.

This will resolve your issue. If still not resolved then try the above procedure by restarting it once.

1. Turn on the machine
2. Press MENU
3. Press SCAN COPY SCAN to enter service mode
4. USE > to got to NVRAM ACCESS
5. Set ABS-M LEVEL to 0
6. Set ABS-P LEVEL to 0
7. Press STOP to EXIT

the solution this is a printhead thermister error. The printhead is reporting either too high or too low temperature. Disconnect the data cables from the printhead and reconnect them making sure that they are in straight. If the problem continues a new printhead must be installed.

if your epson show message of " no maintenance tank"
try this The chips on the waste ink tanks or in the cavity which holds the waste ink tank are not communicating. Make sure the waste ink tank is firmly seated in the printer. If you have replaced the ink tank, I suspect that the chip within the printer is damaged.

Use the following safety guidelines to help ensure your own personal safety and to help protect your
system and working environment from potential damage.Your product uses a printing process that heats the print media, and heat can cause certain media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting appropriate print media to avoid
the possibility of harmful emissions.

download Owner Manual Dell™ Laser Printer 3100cn here

1.) power on (error message)
2.) press the "Stop (triangle)" and the "Colour copy" button and hold them
3.) press the power button to power off, still hold 2.)
4.) press the power button to power on, still holding 2.)
5.) the LEDs start to flash, then they stop to flash and the red exclamation mark starts to flash. Now release 2.)

6.) the LED should say: "Init EEprom"
7.) now press and hold the power button until the printer powers off and powers on again.

The "error message" is gone, the "protection counter" (ssc utility) is back to 0, the printer works so far.
Probably, I'll have to replace the sponge.

1. Remove Other All USB Device Except Mouse.
2.TurnOff Computer.Join The Printer While Computer Is Still Close.
3.Open The Computer.
4.At Printer,I Press One Click Print Buttom.At Print Paper I Also Saw Printer Condition Page.
5.Run The f1660.exe.While Running I don't know this language,I see all word is ???????I can read only V30 Original Firmware Version & V30 Patch Firmware Version.Appear dos window and See Press Any Key To Continue."Need To Press Any Key"
6.I click V30 Patch Fireware Version.And Watch At Printer,After a few seconds, the LED glows orange on the printer,Then Green light blinks 3...4 Time,& Then Still Green.
7. Remove the print cartridge. Refill Toner ,Seal with tape the chip. Insert the cartridge into place.

At Samsung Printer Seeting My cartridge With Full With Black Toner
Download f1660.exe From http://up4vn.com/?d=0CXOZVXM

1. Connect the printer to the computer and turn it on.
2. Print report printer. In 164H, press and hold three to five seconds, press the cancel button. Until the printer are flashing lights.
3. Consider the printout. We are interested in line OS Version. It spelled out the printer firmware version. Looks like this (OS Version 1.01.00.HH)
9. Turning off the computer all USB devices except mouse and treated printer.
10. Run the program firmware f16xx.exe
11. Select the device and firmware version and click the appropriate button. (Say V.30 path firmware)
12. Appear dos window and it will run the point.

Attention. If the points do not run, it means that something went wrong. check the connection and try again.

14. After a few seconds, the LED glows orange on the printer. This is normal. After completing the firmware in 2-3 minutes will restart the printer. He has to rustle engines and calm down.
13. Remove the print cartridge. Seal with tape or remove the chip. Insert the cartridge into place.

Revised unit behaves as follows:

Cartridge with the chip is handled appropriately. Prints until the counter is not empty.
Over the counter - the device is locked.
Cartridge without chip or a sealed chip is treated as a full cartridge. Counter clicks, percent decrease, while the unit does not switch off. If the machine off and on again it starts all over again. Again a full report on the cartridge and counter work.
In the last (Laid here) version fixing boot made in normal mode. Enabled device, pootmenyali installation of new devices and loaded the firmware. Nevertheless, the instruction to stop jammed not hurt. For emergency lifting apparatus. If something went wrong. (The light blinks)

Instructions to stop jammed! (Boot)

1. Disable unnecessary USB devices, leave only the mouse.
2. Connect the unit is turned off the computer.
3. Run the BIOS file f16xx.exe
4. The unit click Stop. And do not go to step 7.!
5. Turn the unit on. In 1660/1665 Start button next to the Stop, at 164h - switch.
6. After two - three seconds the LED on the printer blinks rapidly.
7. Release the button Stop.
8. Select the device and firmware version and click the appropriate button. (Say V.30 path firmware)
9. Appear dos window and it will run the point.
10. After a few seconds, the LED glows orange on the printer. This is normal. After completing the firmware in 2-3 minutes will restart the printer. He has to rustle engines and calm down.
11. Remove the print cartridge. Seal or remove the chip. Insert the cartridge into place.

download firmware here

Machine Error 46 – Purged Ink Box Full MFC620CN/420CN/410CN/210C and FAX2440C

The machine counts all purge (cleaning) operations in order to prevent the internal ink absorber box from overflowing with purged ink. An “initial purge”, for example, advances the purge counter by 187 + 420 = 607. When the purge counter approaches 6400, an internal "Machine Error 46" is generated. Further purge operations are prohibited, and therefore the printer becomes unuseable.

When an internal Machine Error 46 is generated, the user will see an “Unable to Clean” external message and will be unable to use the printer. The “Unable to Clean” external message can relate to many different internal error codes however.

The user can establish the internal Machine Error Code as follows: pull the mains cable out of the machine (power off), hold down the Menu/Set key, re-insert the mains cable into the machine (power on). The internal Machine Error Code will be displayed.

If there is a Machine Error 46, it is necessary to dismantle the printer, replace the ink absorber box (or possibly break the ink absorber box open and clean its absorbent sponges under a tap), re-assemble the printer and reset the purge counter to zero.

Resetting purge counter MFC620CN/420CN/410CN/210C and FAX2440C

1) Enter machine maintenance mode (on MFC210C all four photo/copy/fax/scan lights flash in maintenance mode). Care is needed in maintenance mode, otherwise critical settings may be inadvertently corrupted.

FAX models with numerical keypads: Press the Menu/Set, *, 2, 8, 6 and 4 keys within two seconds. (if you fail to complete the correct key sequence within two seconds, press the Stop key to try again).

Other (non-FAX) models: Press the Menu/Set and Black Start keys. Next press the “up arrow” key four times to enter the maintenance mode).

2) Press the 8 then 0 keys in the initial stage of the maintenance mode to call up the machine's log information list (function code 80).

3) Press the Black Start key several times to scroll through the log information list to reach the purge counter. The purge counter is the 25th item in the list.

4) Press the 2, 7, 8, and 3 keys in this order to reset the purge count to zero.

5) Press the Stop/Exit key to return to the initial stage of the maintenance mode.

6) Press the 9 key twice to return to the standby state.